Categories

Contact Us

Contact Baienwei

Address: No. 13, Baofu Road, Tianbao Industrial District, Baodi, Tianjin,China.

TEL: 86-22-29291825

FAX: 86-22-29291821

Email: alsi@baienwei.com

Website: http://www.alsi-alloys.com

Company News

Home > News > Content
Some Of Heat Treatment Applications In Which Are Active.
Jun 30, 2017

The following description is about the basic knowledge of Al/Aluminum Alloys.

Tag 1: Nomenclature of Al Alloys 

      1xxx => Pure Al

      2xxx => Cu Heat Treatable

      3xxx => Mn

      4xxx => Si

      5xxx => Mg

      6xxx => Mg, Si Heat Treatable

      7xxx => Zn Heat Treatable

      8xxx => Other elements


Tag 2: Forging

The forging of aluminum alloys is the process of converting a uniform blank shape into a final product by hammering the material between shaped or flat dies. This working process may take place in one stage or several stages. The great majority of aluminum forgings are made in the heat-treatable alloys, but forgings in pure aluminum and in some of the non-heat-treatable alloys find application in certain fields. The precision forgings are used for many highly stressed parts, such as in aircraft undercarriage gear, internal combustion engines and other power units. Forged components have an advantage of near net shape, minimized further machining.


Tag 3: Quenching

This is a critical operation and must be carried out to precise limits if optimum results are to be obtained. The objective of the quench is to ensure that the dissolved constituents remain in solution down to room temperature.The speed of quenching is important and the result can be affected by excessive delay in transferring the work to the quench. The latitude for the delay is dependant on section and varies from 5 to 15 seconds for items of thickness varying from 0.4mm to 12.7mm. Generally, very rapid precipitation of constituents commences at around 450°C for most alloys and the work must not be allowed to fall below this temperature prior to quenching.

Another factor to be considered in quenching is the work load and the ability of the quenchant to extract the heat at sufficient rate to achieve the desired results.The usual quenching medium is water at room temperature. In some circumstances slow quenching is desirable as this improves the resistance to stress corrosion cracking of certain copper-free Al-Zn-Mg alloys.Parts of complex shapes such as forgings, castings, impact extrusions and components produced from sheet metal may be quenched at slower quenching rates to improve distortion characteristics.Thus a compromise must be considered to achieve a balance of properties in some instances. Quenchants used in slower quenching applications include water heated to 65-80°C, boiling water, aqueous solutions of polyalkalene glycol or forced air blast.

Tag 4: Annealing

Annealing is applied to both grades to promote softening. Complete and partial annealing heat treatments are the only ones used for the non-heat treatable alloys. The exception is the 5000 series alloys which are sometimes given low temperature stabilisation treatment and this is carried out by the producer.

Annealing is carried out in the range 300-410℃ depending on the alloy. Heating times at temperature vary from 0.5 to 3 hours, conditional on the size of the load and the alloy type. Generally, the time need not be longer than that required to stabilize the load at temperature. Rate of cooling after annealing is not critical.

Where parts have been solution heat-treated a maximum cooling rate of 20℃per hour must be maintained until the temperature is reduced to 290℃.Below this temperature, the rate of cooling is not important.

Tag 5: Melting

Production of high quality semi-finished products and castings based on aluminum depends on quality of raw materials, especially master-alloys and alloying elements. Master-alloy could be considered as an alloying element and the process and the technology of their production should be carefully controlled. Even though master-alloys are for very long time used for the production of aluminum alloys there isn't enough data on them. Therefore a systematic approach is needed to this issue, which includes analysis of theoretical background and practical ways of alloys and master-alloys production.

Every deviation from an optimal regime of alloying with refractory metals will cause significant loss in alloying elements while smelting and shortening of exploitation life of lining. Choice of process for master-alloy production is dependant from several factors: production capacity, demanded quality, smelting and casting equipment etc. For understanding of physical and chemical essence of master-alloys production process, it is necessary to research mechanism and kinetics of interactions of pure metal and its compounds with molten aluminum and principles of interaction of molten aluminum with gaseous components, especially with hydrogen.


Tag 6: Welding

Welding processes are essential for the manufacture of a wide variety of products, such as: frames, pressure vessels, automotive components and any product which have to be produced by welding. However, welding operations are generally expensive, require a considerable investment of time and they have to establish the appropriate welding conditions, in order to obtain an appropriate performance of the welded joint. There are a lot of welding processes, which are employed as a function of the material, the geometric characteristics of the materials, the grade of sanity desired and the application type (manual, semi-automatic or automatic). Some of the most widely used welding process for aluminum alloys,such as shielded metal arc welding (SMAW),gas metal arc welding (GMAW),gas tungsten arc welding (GTAW),friction stir welding (FSW),modified indirect electric arc welding technique (MIEA),and etc.